STR-DA2800ES AV Receiver Firmware Upgrade

This firmware upgrade is currently available which provides the following benefits:

• Support the following HDMI Specification Version 2.0 4K/60p signal
  - 3840x2160p @ 59.94/60Hz *
  - 3840x2160p @ 50Hz *
  - 4096x2160p @ 59.94/60Hz *
  - 4096x2160p @ 50Hz *
  *only YCbCr 4:2:0 / 8bit
  

Note: This update is available only by performing a Network Upgrade. The update file is not available to download and install from this page.

IMPORTANT: This file is only for use with the models identified. Not all models are sold in all countries.

Table of Contents | Go to Top of Page

• Check the Current Firmware Version
• How To Get the Firmware Upgrade
• Network Upgrade Instructions
• Network Firmware Upgrade FAQ
  
  

Check the Current Firmware Version | Go to Table of Contents

1. Power on the television and make sure it is tuned to the inputs to which the AV receiver is connected.
2. Power on the AV receiver.
3. On the AV receiver remote control, press the AMP button, then the HOME button, and then wait until the home menu is displayed on the television before proceeding.
4. Use the arrow keys on the remote control to select "Settings", and then press the ENTER button.
5. Use the arrow keys to select "System Settings", and then press the ENTER button.
6. Use the arrow keys to select "System Information", and then press the ENTER button.
7. The firmware version currently installed on the AV receiver will be listed on the television screen.
   
   If the version number is 1057 or higher, it is not necessary to install this firmware upgrade.
   
   

How To Get the Firmware Upgrade | Go to Table of Contents
The STR-DA2800ES AV receiver firmware can only be upgraded by performing a Network Upgrade.

• To perform the upgrade you will need to connect the AV receiver to your Internet source using an Ethernet cable.
• Please see the Network Upgrade Instructions section below, for more information.
  If you have questions or require assistance, please contact Sony.
  
  

Network Upgrade Instructions | Go to Table of Contents

The STR-DA2800ES AV receiver firmware can only be upgraded by performing a Network Upgrade.

Important Notes

• If you have not done so already, please check the current firmware version to determine if this firmware upgrade is needed for your AV receiver.
• WARNING!! Please follow the upgrade instructions carefully. Failure to follow the instructions may interrupt the upgrade process and may cause the AV receiver to be unresponsive or to require repair.
• WARNING!! Do not power off the AV receiver or disconnect it from the AC power outlet. Loss of power during the installation of the firmware upgrade may cause the AV receiver to be unresponsive or to require repair.
• In order to perform the network upgrade it is necessary to have the receiver correctly connected to an active Internet connection.
• In order to perform the firmware upgrade, it is necessary to have the receiver correctly connected to a compatible television.
• It is highly recommended that you print out these instructions for use as a reference during the installation process.
  
  

Firmware Upgrade Instructions | Go to Table of Contents
WARNING!! Please follow the upgrade instructions carefully. Failure to follow the instructions may interrupt the upgrade process and may cause the AV receiver to be unresponsive or to require repair.

Note: The firmware upgrade process usually takes about 15 to 50 minutes, depending on system configuration and network connection.

1. Power on the television and make sure it is tuned to the inputs to which the AV receiver is connected.
2. Connect the LAN port (switching hub) on the receiver to your Internet source using an Ethernet cable.
3. Power on the AV receiver.
4. On the AV receiver remote control, press the AMP button, then the HOME button, and then wait until the home menu is displayed on the television before proceeding.
5. At the home menu, use the arrow keys on the remote control to select "Settings", and then press the ENTER button..
6. At the Settings menu, use the arrow keys on the remote control to select "Network Update" and then press the ENTER button.
7. The message "Perform version update?" is displayed on the television.
8. Select "OK" and then press the ENTER button.
9. The download process starts and the download screen is displayed on the television.
10. During the download the message "DL */9" is displayed on the television screen.
    Note: The "*" changes to "0" through "9," indicating the download progress.
11. After the download is complete, the upgrade starts and the ON/STANDBY light on the front panel starts blinking.
12. After the upgrade is completed, the AV Receiver will automatically restart.
13. Check the current firmware version to confirm that the upgrade has successfully installed.
    Note: If the version number is 1057, the firmware upgrade was successful.

If you have questions or require assistance, please contact Sony.